1
sono un felice possessore della V3.00B3.DARKWOLF, volevo passare alla routertech 2.96, ma ho dei problemi quando carico il firmware.
A dire il vero è un bel po' di tempo che non cambio firmware, forse ho dimenticato qualcosa!
Ho utilizzato il RUC:
Router Upgrade Check 1.4.1 02/01/2012 04:51:53
Router IP: 192.168.1.1
Description: Dlink G604T
Board type: AR7VW
Product ID: AR7WRD
Bootloader: adam2
RAM 16,0 MB
Flash (ROM) 4,0 MB
ADAM2: Yes
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build:
Firmware version: V3.00B03.DARKWOLF
Firmware stamp: 20060711170926
CPU: MIPS 4KEc V4.8
DSP: 5.00.03.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: Yes
TIAP: No
TNETW: No
Wireless: Yes
WIFI chip: TNETW1130
WIFI chip conf: No
Ports: 4
Ports (according to router): N/A
Marvell (or Marvell like): No
NSP: -sh:
Manufacturers: D-link Corporation
RNDIS:
HRNDIS:
WARNING
Cannot confirm the model number of the wireless chip.
The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again.
Warning! Core Logic (NSP) could not be read. If the Core Logic version is too low you may need to upgrade to your router manufacturer's latest firmware first.
WARNING
Your router does not have a Marvell switch and so your switch is not supported.
Your Ethernet ports may or may not function correctly with a RouterTech firmware.
Select an AR7WRD ADAM2 4 PORT firmware.
Latest: routertech-ar7wrd-adam2-firmware-4ports-20110502.zip
(only contains single firmware image)
Please read the instructions that come with the firmware files before you upgrade.
Note: a later version of the firmware may exist depending on the how up to date the RUC is.
The date-stamp may be superseded, but the rest of the filename should be the same.
With your current MTD values, you have to upgrade your firmware using a single firmware image. Do NOT try to upgrade by using separate config + kernel + filesystem images.
/etc /versions
CUSTOMER=DARKWOLF
MODEL=DSL-G604T
VERSION=V3.00B03.DARKWOLF
HTML_LANG=EN
BOARD=AR7VW
VERSION_ID=
CPUARCH_NAME=AR7
MODEL_ID=
FSSTAMP=20060711170926
#
/proc/wlan
-sh: cd: can't cd to /proc/wlan
#
/usr/sbin/wlan
#
/proc/ticfg/env
memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
ProductID AR7WRD
HWRevision Unknown
SerialNumber 00:0F:3D:FC:EB:6B
my_ipaddress 192.168.1.1
maca 00:0F:3D:FC:EB:6B
usb_vid 0x0
usb_pid 0x0
usb_rndis_mac 00.0d.88.11.03.02
usb_board_mac 00.0d.88.22.03.02
usb_man N/A
usb_prod N/A
usb_serial 1234567890
prompt Adam2_AR7RD
firstfreeaddress 0x9401d328
req_fullrate_freq 125000000
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
autoload 1
mac_ap 00:0F:3D:FC:EB:6C
autoload_timeout 5
mtd4 0x90010000,0x903f0000
StaticBuffer 120
memchk.sh 1
checksync.sh 1
cron_la.sh 2
modulation 0xffff
SW_FEATURES 0X8000
led_conf led.g604t
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
eoc_vendor_id 0x444C696E6B000000
enable_margin_retrain 1
eoc_vendor_serialnum 00:0F:3D:FC:EB:6B_00000000000000
eoc_vendor_revision 20060711
invntry_vernum 2006071100000000
#
/proc/sys/dev/adam2/environment
memsize 0x01000000
flashsize 0x00400000
modetty0 38400,n,8,1,hw
modetty1 38400,n,8,1,hw
bootserport tty0
cpufrequency 150000000
sysfrequency 125000000
bootloaderVersion 0.22.02
ProductID AR7WRD
HWRevision Unknown
SerialNumber 00:0F:3D:FC:EB:6B
my_ipaddress 192.168.1.1
maca 00:0F:3D:FC:EB:6B
usb_vid 0x0
usb_pid 0x0
usb_rndis_mac 00.0d.88.11.03.02
usb_board_mac 00.0d.88.22.03.02
usb_man N/A
usb_prod N/A
usb_serial 1234567890
prompt Adam2_AR7RD
firstfreeaddress 0x9401d328
req_fullrate_freq 125000000
mtd0 0x900a1000,0x903f0000
mtd1 0x90010090,0x900a1000
mtd2 0x90000000,0x90010000
mtd3 0x903f0000,0x90400000
autoload 1
mac_ap 00:0F:3D:FC:EB:6C
autoload_timeout 5
mtd4 0x90010000,0x903f0000
StaticBuffer 120
memchk.sh 1
checksync.sh 1
cron_la.sh 2
modulation 0xffff
SW_FEATURES 0X8000
led_conf led.g604t
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
eoc_vendor_id 0x444C696E6B000000
enable_margin_retrain 1
eoc_vendor_serialnum 00:0F:3D:FC:EB:6B_00000000000000
eoc_vendor_revision 20060711
invntry_vernum 2006071100000000
#
/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (jenny@FD5) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Tue Jul 11 15:23:20 CST 2006
#
/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 149.91
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
#
/proc/avalanche/avsar_ver
ATM Driver version:[5.00.04.00]
DSL HAL version: [5.00.03.00]
DSP Datapump version: [5.00.03.00] Annex A
SAR HAL version: [01.07.2b]
PDSP Firmware version:[0.52]
#
/proc/interrupts
7: 45542 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 473 serial [hw0 (Avalanche Primary)]
23: 0 + SAR [hw0 (Avalanche Primary)]
29: 0 vlynq0 [hw0 (Avalanche Primary)]
41: 1757 + Cpmac Driver [hw0 (Avalanche Primary)]
47: 6 + DSL [hw0 (Avalanche Primary)]
#
/proc/modules
tiatm 130952 0
#
/proc/flashinfo
cat: /proc/flashinfo: No such file or directory
#
/etc/PORTS
cat: /etc/PORTS: No such file or directory
#
logic:status/nspver
-sh: cm_cli_tty: not found
logic:status/has_marvell
-sh: cm_cli_tty: not found
/etc /led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
##################################################################
# The GPIO numbers 0 to 31 ==> correspond to GPIO pins #########
# The GPIO numbers 32,33 are mapped to ADSL (LED) pins ###########
##################################################################
module = adsl # module = {adsl,usb,pppoe,wlan}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 200 # flash on duration in ms
param2 = 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = 33 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 25 # blink/flash rate in ms
######################################################################
module = cpmac # module = {adsl,usb,pppoe,wlan,cpmac}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 15 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 15 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 15 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 15 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
#################################################
module = usb # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = wlan # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = status # module = {adsl,usb,pppoe, status}
state = 0 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = status down, 1 = status active
gpio = 8 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 500 # flash on duration in ms
param2 = 500 # flash off duration in ms
Come consigliato ho messo la versione: routertech-ar7wrd-adam2-firmware-4ports-20110502,
ma quando la carico dal web, torna sempre alla stessa versione che avevo prima. A volte non riesco più a collegarmi al web e devo premere per 30 sec il bottone di reset.
Sto sbagliando qualcosa?
Ps. l'immagine che devo caricare è questa: RouterTech_3.6.0D_20110502_2.96_AR7WRD_Adam2_firmware.upgrade.img?
